Why Use Temperature Transmitters Instead of Direct Wiring?
Mon, 02/05/2007 - 4:20am
This point-by-point comparison examines the advantages and consequencesBy Gary Prentice
Direct wiring strategies have generally been considered less expensive and sometimes easier. Because of cost considerations, transmitters were often reserved for control and applications where signal and loop integrity were a must. Today's highly functional microprocessor-based field-mount temperature transmitters are comparable in price to direct wiring strategies. When the additional advantages of using intelligent transmitters are factored in, you can save considerable time and avoid maintenance headaches. This is especially true when the measurement point is located a long distance from the readout and control system.
Cut Wiring Costs
In retrofit situations, you may want to switch to transmitters, but you may be reluctant to do so because you mistakenly believe that new copper wires must be run to accommodate the 4-20 mA. This is not necessarily the case. Temperature transmitters can be installed at the sensor, and the in-place RTD or thermocouple extension wires can be used to transmit the 4-20 mA back to the control system. The qualifier is resistance.
Because thermocouple wire has higher resistance than copper wire, you should run the resistance calculation on your extension wire to make sure you do not over-burden the temperature transmitter. If these calculations confirm that you can use the existing field wiring, you will have no additional installation time or material costs. And, you still get all the advantages of using temperature transmitters.
Protect Against Plant Noise
In a direct wiring scheme, the low-level signals generated by an RTD (ohm) or thermocouple (mV) are particularly susceptible to the signal-degrading effects of RFI/EMI. Compounding the problem, sensor extension wires can behave much like an RFI/EMI antenna by actually drawing plant noise to the wires and affecting weak, low-level signals.
Conversely, a properly designed temperature transmitter effectively negates the effects of RFI in two ways. If the RFI/EMI is on the temperature sensor, the transmitter's RFI filtering will prevent the noise from propagating to the transmitter's output. If the noise is being picked up on the 4-20 mA side of the transmitter, the 4-20 mA signal strength will be less distorted by the RFI than would a mV level signal. The transmitter's output has a higher signal-to-noise ratio. When specifying your transmitter, always check for RFI/EMI protection. If there is no specification given, it's usually because the instrument is not designed to resist noise. It probably will not perform very well in a noisy plant environment.
Reduce Hardware CostsWith direct wiring, it is necessary to provide temperature input cards for the DCS and PLC. These cards usually cost more per point than does a 4-20 mA input card. If you are using temperature transmitters, the lower cost 4-20 mA input cards help to pay for the transmitters. Additionally, you are keeping in inventory one less board type and reducing another source of maintenance confusion.
With an intelligent temperature transmitter, you can simply change out the sensor and reconfigure the transmitter to accommodate the different sensor type. The loop's twisted pair wiring and existing 4-20 mA input boards don't even have to be touched. Because you never know what sensor you'll end up with, make sure you select a universal transmitter that configures to accept all common temperature sensor types and temperature ranges.
You gain more application flexibility if you use a temperature transmitter with adequate input/output isolation. Temperature sensors insulated with MgO will eventually go to ground. If the sensor is an RTD, you must discard it and buy new. But if that sensor is a TC and you have isolation elsewhere in the measurement loop, the grounded TC still provides a valid temperature measurement. If you place the loop isolation in the transmitter, you gain the flexibility of being able to use non-isolated 4-20 mA input cards, which are generally the least expensive input cards. If all your TCs are grounded, no error-causing ground loops can occur when you use isolated TTs.
Enhance Accuracy and Stability
If you need even better accuracy, you can trim a universal transmitter to precisely match a particular sensor. Even though sensors are designed to have a high degree of conformance to an established curve, each one even precision sensors will vary slightly from its stated specification. By using the TT electronics to match the TT to the sensor, you eliminate this final bit of error.
It's called sensor-to-transmitter trimming. The transmitter is connected to the sensor and then immersed in calibration baths maintained at stabilized temperatures. The transmitter then "captures" two readings from the sensor, representing the upper and lower range values , and stores them in non-volatile memory. The transmitter uses these values to compensate for deviations between the sensor's stated linearization curve and its actual measurements. When transmitters are paired with a 1,000 ohm RTD, this technique results in the amazing measurement accuracy of up to ±0.014°C (±0.025°F) over a 100-degree span.
To further enhance measurement accuracy, some transmitters can be trimmed to respond to two data points within the selected zero and span measurement range. This advantage allows a complete range to be monitored, while placing measurement emphasis on a specific segment of the range most critical to the process.
Throughout the lifetime of a process, enhancements are routinely made to accommodate the manufacture of upgraded or even completely new products. Process changes may require different measurement ranges or greater temperature accuracy than was previously required. Either of these conditions may necessitate a change in the type of sensors that are used.
Lower Maintenance ExpensesTemperature transmitters have come a long way since the days of fixed-range, inflexible instruments. Some transmitters are not only universal in regards to input type and range, but they also incorporate powerful sensor diagnostics that save considerable time and money.
Temperature transmitters with intelligent diagnostic capabilities help you keep track of sensor operation and quickly find and diagnose sensor failures. Capable of continually monitoring the sensor, if a wire breaks or otherwise stops sending a signal during operation, the transmitter sends the output upscale or downscale to warn of sensor burnout and other unwanted conditions.
Furthermore, the transmitters can tell you which wire has broken via an error message either on an integral digital display or using PC configuration software. Specific fault messages eliminate the work of removing the sensor or checking all the lead wires to diagnose a problem. During startups, in the middle of the night, or in the middle of winter, this can be a huge time-saving advantage.
Avoid Lead Wire Imbalances
Intelligent temperature transmitters are capable of accepting "true" four-wire RTD inputs and provide a constant current source to the outer leads of the RTD. The voltage drop is measured across the inner leads, which is a high impedance loop. Because there is essentially no current flow in the voltage loop, voltage is directly proportional to RTD resistance. Lead resistance is ignored. You will get a very accurate measurement providing the resistance value of the RTD plus corrosion, plus wire resistance is less than 2,000 ohms (typically). A four-wire RTD costs about the same as a three-wire and can be used with less expensive, smaller gauge wire without concern for added resistance.
Gary Prentice is a temperature applications engineer at Moore Industries-International Inc., a leader in signal interface instruments for industrial process control, system integration, and factory automation. More information is available by calling 518-399-4747, sending an e-mail to email@example.com, or visiting www.miinet.com.